Behringer X32 Guia de Início Rápido

The Engineers’Quick Start Guide

Using DCA GroupsUse DCA Groups to control the volume of multiple channels with a single fader.1. To assign a channel to a DCA, rst be sure you have

Sends on FaderTo use “Sends on Faders,” press the “Sends on Faders” button located near the middle of the console.• You can now use “Sends On Faders”

Mute Groups1. To assign/remove a channel from a Mute Group, press the MUTE GRP button near the screen. You will know you are in edit mode when the M

Assignable Controls1. The X32 features user-assignable rotary encoders and buttons in 3 layers. To assign them, press the “view” button near the ASS

FX Rack1. Press the EFFECTS button near the screen to see an overview of the 8 stereo FX processors. Keep in mind that FX slots 1-4 are for “Send”

Setting up P161. Setup the P16 outputs by pressing the ROUTING button and paging over to “P16 Out”. 2. Select an output channel and then select a si

Setting up S16 Stagebox1. Connect the AES50 (A) port on the back of the X32 to the AES50 (A) port on the back of the S16 stagebox. If using two S1

iPad Conguration1. Download the Xi Control app for free from the Apple App Store.2. Connect the X32 “Ethernet” jack to an available port on a wirel

PC / Mac Control Conguration1. Download the latest version of Xcontrol from www.behringer.com/x32.2. Connect the X32 “Ethernet” jack to a wireless

Firewire / USB Card1. Press the SETUP button near the screen, and use the PAGE SELECT buttons to select the “card” tab.2. Choose either USB or Firew

DAW Control1. Press the SETUP button and page right to the ”remote” tab.2. Enable the Remote Selection button by pressing the rst rotary encoder.3.

Using the Talkback Section1. The X32 has the option of using the built in talkback mic or external mic.2. To begin, press view near the Talkback Sec

Saving a Scene1. Access the SCENE menu by pressing the “view” button.2. Use the 4th rotary encoder below the screen to select a scene location numbe

Using Preset Libraries1. The X32 has separate preset libraries for Channel Strip, Eects, and Routing. To access them, use the LIBRARY button near t

Copy / Paste1. Copy and Paste functions can be accessed from the UTILITY button.2. To copy settings for a specic processor, such as a channel compr

X32 as Monitor Console Setting up a “Cue Wedge” The Solo Options determine what signal arrives at the monitor outputs. As you cycle through the solo

Dedicated Monitor / Control Room outputs for Studio Monitors or “Cue Wedge”AES502 X AES50 Digital I/O for connectivity to S16 Digital Snake via stand

Vital Specs• 32MIDASDesignedMicPreamps– Plus6AUX¼"TRSLineInputs• 16XLROutputs– Plus6AUX¼"TRSLineOutputs• 25MixBusse

Firmware Updates / USB Stick RecordingTo Update Firmware:1. Go to behringer.com/X32 and click the “Downloads” tab. Download the latest rmware to yo

Routing Menu1. The rst page of the ROUTING menu is where you choose which inputs the X32 will route to the 32 input channels, (in banks of 8).• L

Editing Channel Strip LCDs1. Hold down the select button for the channel you wish to change and press UTILITY.2. Use the rotary encoders below the s

Using BussesBus Terminology Explained:Unlike other consoles, the X32 uses ONLY Busses for Sends (no AUX Sends).You can use these 16 busses for whateve

Matrix Mixes• Matrix mixes can be fed from any mix bus as well as the MAIN LR and Center/Mono bus.• To send to a Matrix, rst press the select butto