Behringer SRC2000 Manual do Utilizador descarregar pdf (Página 4)

4. Specifications

5. Warranty

§ 1 WARRANTY CARD

To be protected by this warranty, the buyer must complete and return the enclosed

warranty card (signed/stamped by retail dealer) within 14 days of the date of pur-

chase to BEHRINGER INTERNATIONAL (address see § 3). Failure to return

the card in due time (date as per postmark) will void any extended warranty

claims.

§ 2 WARRANTY

BEHRINGER INTERNATIONAL warrants the mechanical and electronic com-

ponents of this product to be free of defects in material and workmanship for

a period of one (1) year from the original date of purchase, in accordance with

the warranty regulations described below. If any defects are found in the

materials or workmanship, or if the product fails to function properly within

the specified warranty period, BEHRINGER INTERNATIONAL shall, at its

sole discretion, either repair or replace the product. If the warranty claim

proves to be justified, the product will be returned freight prepaid by

BEHRINGER INTERNATIONAL within Germany. Outside of Germany, the

product will be returned at the buyers expense.

Warranty claims other than those indicated above are expressly excluded.

§ 3 RETURN AUTHORIZATION NUMBER

To obtain warranty service, the buyer must call Behringer GmbH during normal

business hours BEFORE returning the product (Tel.: +49 (0) 21 54 / 92 06 66).

All inquiries must be accompanied by a description of the problem.

BEHRINGER INTERNATIONAL will then issue a return authorization number.

The product must be returned in its original shipping carton, together with the

return authorization number, to the following address:

BEHRINGER INTERNATIONAL GmbH

Service Department

Hanns-Martin-Schleyer-Str. 36-38

D - 47877 Willich-Münchheide

Shipments without freight prepaid will not be accepted.

§ 4 WARRANTY REGULATIONS

Warranty services will be furnished only if the product is accompanied by an original

retail dealers invoice. Any product deemed eligible for repair or replacement

by BEHRINGER INTERNATIONAL under the terms of this warranty will be

repaired or replaced within 30 days of receipt of the product at BEHRINGER

INTERNATIONAL. If the product needs to be modified or adapted in order to

comply with applicable technical or safety standards on a national or local

output. The headphones amp is connected to 23 & 24, which are normalled and connected to the control room

outputs of the mixing console. Of course, you can also use pre-fader aux paths for the headphones mix.

Patchbay

manages the dynamics and frequency-processing devices in an open configuration (modules 1

through 16). Multigates and compressors should be used here, in particular. Modules 17 through 24 are used to

provide a parallel split, i.e. two modules are patched to each other on the rear with one patch cord, so that you can

split up a signal applied on the front panel to several destinations. These modules have a parallel configuration.

It should be noted that patchbays should be placed one below the other in such a way that the patch cords wont hang

all over the patchbays. In our example you dont have to span great distances, for instance, to patch the dynamics and

EQs to the insert paths.

3. Looming problems

Loom wiring is an art unto itself, and it is worth taking time out to get it right. First off, it is important to avoid earth loops

(a looped wire acts an aerial, picking up hum and electromagnetic radiation). Think of a tree. Every part of that tree is

connected to every other part, but only by one route. Thats how the total earth picture for your entire studio should look.

Dont take the earth off your power cable plug to reduce audible 50 Hz mains hum. Rather you should be looking at

disconnecting the signal screen somewhere (one or several audio cables).

It is good practice to ensure that all screens are commoned at the patchbay, in which case all unearthed equipment

would pick up earth from this point via a single screen (more than one route = an earth loop), while mains-earthed

equipment would have all screens cut at the equipment end.

Some quality equipment has an independent signal and mains earth. In this case at least one screen should carry earth

to the equipment. Sometimes the only way to find out is suck and see.

Take care to ensure that using the patchbay does not disturb the studios earth architecture. Always use short as

possible patch leads with the screen connected at both ends.

Having designed mains hum out of the system, make up your cable looms from the patchbays outwards, and use cable

ties, flexible sheaths, multicores, etc. to keep the back of your racks tidy.

Connectors 1/4 jack unbalanced

BEHRINGER is constantly striving to maintain the highest professional

standards. As a result of these efforts, modifications may be made from

time to time to existing products without prior notice. Specifications and

appearance may differ from those listed or shown.

Dimensions

Width 482.6 mm (19)

Height 1 HU

Depth 93 mm

Weight ca. 1,8 kg

level, in any country which is not the country for which the product was

originally developed and manufactured, this modification/adaptation shall

not be considered a defect in materials or workmanship. The warranty

does not cover any such modification/adaptation, irrespective of whether

it was carried out properly or not. Under the terms of this warranty,

BEHRINGER INTERNATIONAL shall not be held responsible for any cost

resulting from such a modification/adaptation. Free inspections, mainte-

nance/repair work and replacement of parts are expressly excluded from

this warranty, if caused by normal wear of the product.

Damages/defects caused by the following conditions are not covered by

this warranty:

s misuse, neglect or failure to operate the unit in compliance with the

instructions given in the user or service manuals.

s connection or operation of the unit in any way that does not comply

with the technical or safety regulations applicable in the country where

the product is used.

s damages/defects that are caused by force majeure or by any other

condition beyond the control of BEHRINGER INTERNATIONAL.

Any repair carried out by unauthorized personnel will void the warranty. Prod-

ucts which do not meet the terms of this warranty will be repaired exclusively at

the buyers expense. BEHRINGER INTERNATIONAL will inform the buyer

of any such circumstance. If the buyer fails to submit a written repair

order within 4 weeks after notification, BEHRINGER INTERNATIONAL

will return the unit C.O.D. with a separate invoice for freight and packing.

Such cost will also be invoiced separately when the buyer has sent in a

written repair order.

§ 5 WARRANTY TRANSFERABILITY

This warranty is extended exclusively to the original buyer (customer of retail

dealer) and is not transferable to anyone who may subsequently purchase this

product. No other person (retail dealer, etc.) shall be entitled to give any war-

ranty promise on behalf of BEHRINGER INTERNATIONAL.

§ 6 CLAIM FOR DAMAGES

Failure of BEHRINGER INTERNATIONAL to provide proper warranty

service shall not entitle the buyer to claim (consequential) damages. In no

event shall the liability of BEHRINGER INTERNATIONAL exceed the

invoiced value of the product.

§ 7 OTHER WARRANTY RIGHTS

This warranty does not exclude or limit the buyers statutory rights provided by

national law, in particular, any such rights against the seller that arise from a

legally effective purchase contract.

1 2 3 4

Comentários a estes Manuais

Sem comentários

Behringer SRC2000 Manual do Utilizador Página 4

Comentários a estes Manuais

Manuais e produtos relacionados com Amplificadores áudio Behringer SRC2000